tel call at 008613167029626

email leave a message info@bearings-factory.com

banner
Introduction to Bearings
home Introduction to Bearings

Introduction to Bearings

  • What Is High Temperature Bearing
    • Jul , 31 2020

    What Is High Temperature Bearing? Bearings which can operating at temperature higher than 120°C are  is called high temperature bearings. High-temperature bearings are with bearing rings and rolling elements are tempered at high temperature, the working temperature can reach 150 ° ~ 350 ° ,but the hardness of the bearing is reduced. Imported high temperature bearings can reach a maximum of 98...

  • How Much Grease Should You Put In A Bearing?
    • Jul , 27 2020

    In order to better extend the service life of the motor bearings and ensure the normal operation of the bearings, the motor bearings need to be lubricated and maintained regularly. The main effect of grease on motor bearings is lubrication, protection and sealing. Many details should be paid attention to in the motor lubrication and maintenance, such as: how much do you need to add for the first t...

  • The Advantages of Ceramic Bearing ?
    • Jul , 24 2020

    The Advantages Of Ceramic Ball Bearings : 1. High speed: Ceramic bearings have the advantages of cold resistance, small force elasticity, high pressure resistance, poor thermal conductivity, light weight, and low friction coefficient. They can be applied to high-speed spindles at 12,000 rpm to 75,000 rpm and other high-speed spindles. Precision equipment; 2. High temperature resistance: ...

  • How to Repair and Maintain Automobile Wheel Bearings?
    • Jul , 20 2020

    How to repair and maintain auto wheel bearings? Wheel bearings are important  parts of auto car. The hub axle is responsible for reducing the frictional resistance when the chassis is running and maintaining the normal driving of the car. If the hub bearing fails, it may cause noise, bearing heating, etc., especially the front wheel is more obvious, and it is easy to cause dangerous phenomena...

  • How To Add Grease Into Ceiling Fan bBearings
    • Jul , 16 2020

    How to add grease to ceiling fan bearings? After three to five years of use of the household ceiling fan, if there is resistance or noise, it indicates that the bearing of the ceiling fan motor is worn or poorly smooth, and it should be treated hygienically and filled with smooth grease. When adding grease to the bearing, you need to disassemble the ceiling fan motor and then check the bearing wea...

  • The Difference Between High-Speed Bearings And Low-Speed Bearings
    • Jul , 15 2020

    1. The basis for distinguishing between high-speed bearings and low-speed bearings: Because of the different ways of use, bearings can be divided into high-speed bearings and low-speed bearings, but although this is said, their distinction is not simply based on how many revolutions can be turned to count, and some low-speed bearings per minute The rotation speed can reach nearly tens of thousands...

  • How To Identify Whether The Bearing Lubricant Has Deteriorated
    • Jul , 15 2020

    The bearing lubricating oil is dark black, rich in foam and has emulsified phenomenon. It is grinded with fingers without stickiness, astringency or odor. It is dark brown on the white test paper, and there are no yellow infiltration areas or black spots. If it is not replaced in time, it will accelerate the wear of parts, affect the service life, and even cause safety accidents. Therefore, it is ...

  • What Are Ball Bearings Made of?
    • Jul , 10 2020

    Bearings are the main components of mechanical equipment, and the produced materials used are different too. Deep groove bearings are the most common type of ball bearings. The basic type of deep groove ball bearings are composed of inner ring, outer ring, balls, cage, lubricant, mainly according to the different places of use, we can be roughly divided into four materials. Analysis of four common...

  • How to Produce Bearing Balls?
    • Jul , 08 2020

    1.Heading: In the first step, heading machines cut wire into short lengths and form it into spherical shapes between dies. Deflashing: The flash line, a ridge left by the forming dies, is removed as balls roll between heavy, cast iron plates. 2.Soft Grinding: Similar to deflashing, except that a grinding stone is used to improve precision. 3.Heat-treating: Carbon steel balls are next carburized an...

  • What Are The Common Types of Motorcycle Bearings?
    • Jul , 07 2020

    Motorcycle wheel bearing is type of deep groove ball bearings. The following are some of the most common deep groove ball bearings 6001ZZ, 60012RSR, 600-2ZR, 6002-2RSR, 6003 -ZZ , 6003-2RSR, 6004, 6200, 6201, 6202, 6203, 6204, 6205, 6206, 6300 ZZ BEARING is motorcycle bearing manufacturers,for more information just contact with us . www.TMB Bearing

copyright © 2021 ZZ Bearing (Shanghai) Co., Ltd

top